Hebei Anping Today Chamber of Commerce INC.

Stainless Steel Wire Mesh

Stainless steel wire mesh is wear-resisting, heat-resisting, acid-resisting and corrosion-resisting, so it is extensively used in the chemical industry, pharmaceutical industry, food industry and mining. Woven patterns applied for stainless steel wire mesh or wire cloth can be plain weave, twill weave, Dutch plain weave or Dutch twill weave.

Materials: stainless steel type 304, type 304L, type 316, type 316L, etc.

Plain Weave: this is the most commonly used and simplest wire cloth. Each warp wire crosses alternately above and below each weft wire. It has an extremely wide range of applications

Twilled Weave: it is produced by passing each fill wire alternately over and under two warp wires.

Specification List of Stainless Steel Wire Mesh-Plain & Twilled Weave

Mesh	Wire Gauge		Aperture		Percentage of Opening (%)
Mesh	inch	mm	inch	mm	Percentage of Opening (%)
1×1	0.092	2.34	0.908	23.06	82.4
2×2	0.072	1.83	0.428	10.87	73.3
3×3	0.054	1.37	0.279	7.09	70.1
4×4	0.063	1.60	0.187	4.75	56.0
4×4	0.047	1.19	0.203	5.16	65.9
5×5	0.035	0.89	0.165	4.19	68.1
5×5	0.047	1.19	0.153	3.89	58.5
6×6	0.035	0.89	0.132	3.35	62.7
6×6	0.041	1.04	0.126	3.20	57.2
8×8	0.028	0.71	0.097	2.46	60.2
8×8	0.035	0.89	0.090	2.29	51.8
10×10	0.025	0.635	0.075	1.905	56.3
10×10	0.032	0.813	0.068	1.727	46.2
12×12	0.020	0.508	0.063	1.600	57.2
12×12	0.028	0.711	0.055	1.397	43.6
14×14	0.020	0.508	0.051	1.295	51.0
14×14	0.025	0.635	0.046	1.168	41.5
16×16	0.018	0.457	0.0445	1.130	50.7
16×16	0.023	0.584	0.0400	1.016	39.9
18×18	0.018	0.457	0.0380	0.965	45.8
18×18	0.023	0.584	0.0330	0.838	35.3
20×20	0.016	0.406	0.0340	0.864	46.2
20×20	0.023	0.584	0.0270	0.686	29.2
24×24	0.014	0.356	0.0280	0.711	44.2
24×24	0.016	0.406	0.0260	0.660	38.0
30×30	0.011	0.279	0.0220	0.559	44.8
30×30	0.014	0.356	0.0190	0.483	33.5
35×35	0.0095	0.241	0.0190	0.483	44.7
35×35	0.012	0.305	0.0170	0.432	33.8
40×40	0.008	0.203	0.0170	0.432	46.2
40×40	0.011	0.279	0.0140	0.356	31.4
50×50	0.0055	0.140	0.0145	0.368	52.6
50×50	0.0090	0.229	0.0110	0.279	30.3
60×60	0.0060	0.152	0.0107	0.272	41.2
60×60	0.0075	0.191	0.0092	0.234	30.5
60×60	0.0090	0.229	0.0080	0.203	21.3
70×70	0.0060	0.152	0.0083	0.211	33.8
70×70	0.0070	0.178	0.0073	0.185	26.1
80×80	0.0050	0.127	0.0075	0.191	36.0
80×80	0.0070	0.178	0.0055	0.140	19.4
90×90	0.0050	0.127	0.0060	0.152	30.1
90×90	0.0060	0.152	0.0051	0.130	21.1
100×100	0.0035	0.089	0.0065	0.165	42.3
100×100	0.0040	0.102	0.0060	0.152	36.0
100×100	0.0045	0.114	0.0055	0.140	30.3
120×120	0.0037	0.094	0.0046	0.117	30.7
150×150	0.0026	0.066	0.0041	0.104	37.4
160×160	0.0025	0.064	0.0038	0.097	36.4
180×180	0.0023	0.058	0.0033	0.084	34.7
180×180	0.0018	0.046	0.0038	0.097	46.0
200×200	0.0023	0.058	0.0027	0.069	29.2
200×200	0.0021	0.053	0.0029	0.074	33.6
200×200	0.0016	0.041	0.0034	0.086	46.2
250×250	0.0016	0.041	0.0024	0.061	36.0
270×270	0.0016	0.041	0.0021	0.053	32.2
300×300	0.0015	0.038	0.0018	0.046	29.7
325×325	0.0014	0.036	0.0017	0.043	30.0
400×400	0.0010	0.025	0.0015	0.038	36.0
500×500	0.0010	0.025	0.0010	0.025	25.0
635×635	0.0008	0.020	0.0008	0.020	25.0

Plain Dutch Weave: woven as the plain weave, but with the warp wires of greater diameter than the weft wires. This weave results in greater strength with very fine openings.

Specification List of S.Steel Woven Wire Mesh-Plain Dutch Weave

Mesh/Inch	Wire Diameter	Absolute Filtration Fineness µm	Nominal Filtration Fineness µm
8X85	.014X.0126	318 - 340	250 - 255
12X64	.024X.0165	270 - 285	200 - 205
14X88	.020X.013	225 - 245	150 - 155
20X150	.0098X.007	155 - 165	100 - 105
24X100	.015X.010	115 - 125	80 - 85
30X150	.009X.007	95 - 100	65 - 70
40X200	.007X.0055	65 - 70	55 - 60
50X250	.0055X.0045	55 - 60	40 - 45
80X400	.0049X.0028	43 - 48	35 - 40

Twilled Dutch Weave: each weft wire passes alternately over two, and then under two successive warp wires and each warp wire passes alternately over two and under two successive weft wire.

Specification List of Stainless Steel Woven Wire Mesh-Twilled Dutch Weave

Mesh/Inch	Wire Diameter	Absolute Filtration Fineness µm	Nominal Filtration Fineness µm
20x250	.0098x.0079	110-120	98-105
30x360	.0098x.0060	90-100	80-84
40x560	.0070x.0040	70-75	47-52
120x400	.0040x.0025	50-55	37-43
120x160	.0040x.0025	40-45	28-32
80x700	.0040x.0030	35-40	24-26
200x600	.0024x.0018	28-32	19-21
165x800	.0028x.0020	24-26	14-16
165x1400	.0028x.0016	16-18	9-11
200x1400	.0028x.0016	12-14	5-6
250x1400	.0022x.0016	11-12	3-4
325x2300	.0015x.0010	8-9	2-3

Remark: a. other sizes not listed can be produced upon request.
b. special specification also can be produced upon request.